¶ Step 1 - Prepare the following parts
- 4x T-Slot extrusion 3030 - 160mm
- 4x T-Slot extrusion 3030 - 400mm
- 4x T-Slot extrusion 3030 - 480mm
- 8x Hidden three way corners + 32 M6x8 Set Screws
- 4x vc4_magnet_frame
- 4x M6x12 Cap Head Screw
- 4x 3030 Drop-in T-Nut - M6
- 4x Magnet - Neodymium disc 10x4mm
¶ Step 2 - Hidden three way corners (x8)
- 4x M6x8 Set Screw
- Hidden Three Way Corner
- Insert the set screws into the part's threads.
¶ Step 3 - Assemble the frame - Part 1
- 2x Hidden three-way corner assembly from the last step
- 1x T-Slot extrusion 3030 - 160mm
- Ensure the extrusions are flush and square with the hidden three way corner assembly before and after tightening the screws.
- Tighten the M6x8 set screws.
- Be careful while tightening the set screws, extreme force may break the three way hidden corner.
- Prepare two assemblies
- 2x T-Slot extrusion 3030 - 400mm
- Assemble the parts as shown.
¶ Step 4 - Assemble the frame - Part 2
- Tighten the M6x8 set screws.
- Be careful while tightening the set screws, extreme force may break the three way hidden corner.
- 4x T-Slot extrusion 3030 - 448mm
- Insert the T-slot Exstrusions in the three way hidden corner as shown.
- Tighten the M6x8 set screws.
- Ensure the extrusions are flush and square with the hidden three way corner assembly before and after tightening the screws.
- Be careful while tightening the set screws, extreme force may break the three way hidden corner.
¶ Step 5 - Assemble the frame - Part 3
- Fram assembly from Step 2
- Insert the T-slot Exstrusions in the three way hidden corner as shown.
- Tighten the M6x8 set screws.
- Ensure the extrusions are flush and square with the hidden three way corner assembly before and after tightening the screws.
- Be careful while tightening the set screws, extreme force may break the three way hidden corner.
¶ Step 6 - Assemble the frame magnet mounts
- vc4_magnet_frame
- Magnet - Neodymium disc 10x4mm
- 3030 Drop-in T-Nut - M6
- M6x12 Cap Head Screw
- Loosely thread the 3030 T-Nuts onto the M6x12 screws. Do not tighten them at this point.
- Please verify the magnet polarity in relation to the magnets on the door panel. If the polarity is inverted, the magnets will repel each other instead of attracting.
- Prepare 4 assemblies
¶ Step 7 - Assemble the frame magnets
- Position the magnet mount assembly as shown.
- Push it down so it sits flush with both extrusions.
- Position the remaining magnet mount assemblies as shown.
¶ Step 8 - Install the panel grommets
- 2x ucee_grommet_45mm
- 2x ucee_grommet_80mm
- ucee_grommet_90mm
- ucee_grommet_107mm
- Rat Rig Universal CNC Electronics Enclosure - Components Upper
- Rat Rig Universal CNC Electronics Enclosure - Components Lower
- Insert the grommets into place, they should click in place.
¶ Step 9 - Assemble the PTFix Blocks
- GND PTFix block
- +24V PTFix block
- 4x M2.5 Cap Head Screw
- 4x M2.5 Nylon Locking Nut
- Mains volatage PTFix block
- 2x M2.5 Cap Head Screw
- 2x M2.5 Nylon Locking Nut
- Using the Screws and Nylon Locking Nuts secure the PTFix blocks to the rear of the electronics panels.
¶ Step 10 - Assemble the cable guides
- (26x) M3x6 Cap Head Screw + M3 Washer
- Insert a screw and washer from the front of the plate in every marked hole
- Secure the eight vc4_cable_guide_4 assembly using M3x6 screws and heat inserts in the back at the designated locations.
- Secure the five vc4_cable_guide_5 assembly using M3x6 screws and heat inserts in the back at the designated locations.
¶ Step 11 - Install the electronics panels - Part 1
- 12x M5x12 Cap Head Screws
- 12x 3030 Drop-in T-Nut - M5
- Insert a Screw and T-nut on every marked hole
¶ Step 12 - Install the electronics panels - Part 2
- Insert the panels into the frame as shown.
- Ensure the lower panel is aligned flush with the bottom extrusion, then securely tighten the screws.
- Ensure the top panel is aligned flush with the top extrusion, then securely tighten the screws.